------------------------------------------------------------------------------- -- ____ ____ -- / /\/ / -- /___/ \ / Vendor: Xilinx -- \ \ \/ Version : 2.7 -- \ \ Application : 7 Series FPGAs Transceivers Wizard -- / / Filename : uhtr_trigpd_gt.vhd -- /___/ /\ -- \ \ / \ -- \___\/\___\ -- -- -- Module uHTR_trigPD_GT (a GT Wrapper) -- Generated by Xilinx 7 Series FPGAs Transceivers Wizard -- -- -- (c) Copyright 2010-2012 Xilinx, Inc. All rights reserved. -- -- This file contains confidential and proprietary information -- of Xilinx, Inc. and is protected under U.S. and -- international copyright and other intellectual property -- laws. -- -- DISCLAIMER -- This disclaimer is not a license and does not grant any -- rights to the materials distributed herewith. Except as -- otherwise provided in a valid license issued to you by -- Xilinx, and to the maximum extent permitted by applicable -- law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND -- WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES -- AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING -- BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON- -- INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and -- (2) Xilinx shall not be liable (whether in contract or tort, -- including negligence, or under any other theory of -- liability) for any loss or damage of any kind or nature -- related to, arising under or in connection with these -- materials, including for any direct, or any indirect, -- special, incidental, or consequential loss or damage -- (including loss of data, profits, goodwill, or any type of -- loss or damage suffered as a result of any action brought -- by a third party) even if such damage or loss was -- reasonably foreseeable or Xilinx had been advised of the -- possibility of the same. -- -- CRITICAL APPLICATIONS -- Xilinx products are not designed or intended to be fail- -- safe, or for use in any application requiring fail-safe -- performance, such as life-support or safety devices or -- systems, Class III medical devices, nuclear facilities, -- applications related to the deployment of airbags, or any -- other applications that could lead to death, personal -- injury, or severe property or environmental damage -- (individually and collectively, "Critical -- Applications"). Customer assumes the sole risk and -- liability of any use of Xilinx products in Critical -- Applications, subject only to applicable laws and -- regulations governing limitations on product liability. -- -- THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS -- PART OF THIS FILE AT ALL TIMES. library ieee; use ieee.std_logic_1164.all; use ieee.numeric_std.all; library UNISIM; use UNISIM.VCOMPONENTS.ALL; --***************************** Entity Declaration **************************** entity uHTR_trigPD_GT is generic ( -- Simulation attributes GT_SIM_GTRESET_SPEEDUP : string := "FALSE"; -- Set to "true" to speed up sim reset RX_DFE_KL_CFG2_IN : bit_vector := X"301148AC"; PMA_RSV_IN : bit_vector := x"00018480"; PCS_RSVD_ATTR_IN : bit_vector := X"000000000000" ); port ( --------------------------------- CPLL Ports ------------------------------- CPLLFBCLKLOST_OUT : out std_logic; CPLLLOCK_OUT : out std_logic; CPLLLOCKDETCLK_IN : in std_logic; CPLLREFCLKLOST_OUT : out std_logic; CPLLRESET_IN : in std_logic; -------------------------- Channel - Clocking Ports ------------------------ GTREFCLK0_IN : in std_logic; ---------------------------- Channel - DRP Ports -------------------------- DRPADDR_IN : in std_logic_vector(8 downto 0); DRPCLK_IN : in std_logic; DRPDI_IN : in std_logic_vector(15 downto 0); DRPDO_OUT : out std_logic_vector(15 downto 0); DRPEN_IN : in std_logic; DRPRDY_OUT : out std_logic; DRPWE_IN : in std_logic; ------------------------------- Clocking Ports ----------------------------- QPLLCLK_IN : in std_logic; QPLLREFCLK_IN : in std_logic; ------------------------------ Power-Down Ports ---------------------------- RXPD_IN : in std_logic_vector(1 downto 0); TXPD_IN : in std_logic_vector(1 downto 0); --------------------- RX Initialization and Reset Ports -------------------- RXUSERRDY_IN : in std_logic; -------------------------- RX Margin Analysis Ports ------------------------ EYESCANDATAERROR_OUT : out std_logic; ------------------------- Receive Ports - CDR Ports ------------------------ RXCDRLOCK_OUT : out std_logic; ------------------ Receive Ports - FPGA RX Interface Ports ----------------- RXUSRCLK_IN : in std_logic; RXUSRCLK2_IN : in std_logic; ------------------ Receive Ports - FPGA RX interface Ports ----------------- RXDATA_OUT : out std_logic_vector(31 downto 0); ------------------- Receive Ports - Pattern Checker Ports ------------------ RXPRBSERR_OUT : out std_logic; RXPRBSSEL_IN : in std_logic_vector(2 downto 0); ------------------- Receive Ports - Pattern Checker ports ------------------ RXPRBSCNTRESET_IN : in std_logic; ------------------ Receive Ports - RX 8B/10B Decoder Ports ----------------- RXDISPERR_OUT : out std_logic_vector(3 downto 0); RXNOTINTABLE_OUT : out std_logic_vector(3 downto 0); --------------------------- Receive Ports - RX AFE ------------------------- GTXRXP_IN : in std_logic; ------------------------ Receive Ports - RX AFE Ports ---------------------- GTXRXN_IN : in std_logic; -------------------- Receive Ports - RX Equailizer Ports ------------------- RXLPMHFHOLD_IN : in std_logic; RXLPMLFHOLD_IN : in std_logic; --------------- Receive Ports - RX Fabric Output Control Ports ------------- RXOUTCLK_OUT : out std_logic; ------------- Receive Ports - RX Initialization and Reset Ports ------------ GTRXRESET_IN : in std_logic; RXPMARESET_IN : in std_logic; ------------------- Receive Ports - RX8B/10B Decoder Ports ----------------- RXCHARISK_OUT : out std_logic_vector(3 downto 0); -------------- Receive Ports -RX Initialization and Reset Ports ------------ RXRESETDONE_OUT : out std_logic; --------------------- TX Initialization and Reset Ports -------------------- GTTXRESET_IN : in std_logic; TXUSERRDY_IN : in std_logic; ------------------ Transmit Ports - FPGA TX Interface Ports ---------------- TXUSRCLK_IN : in std_logic; TXUSRCLK2_IN : in std_logic; ------------------ Transmit Ports - TX Data Path interface ----------------- TXDATA_IN : in std_logic_vector(31 downto 0); ---------------- Transmit Ports - TX Driver and OOB signaling -------------- GTXTXN_OUT : out std_logic; GTXTXP_OUT : out std_logic; ----------- Transmit Ports - TX Fabric Clock Output Control Ports ---------- TXOUTCLK_OUT : out std_logic; TXOUTCLKFABRIC_OUT : out std_logic; TXOUTCLKPCS_OUT : out std_logic; --------------------- Transmit Ports - TX Gearbox Ports -------------------- TXCHARISK_IN : in std_logic_vector(3 downto 0); ------------- Transmit Ports - TX Initialization and Reset Ports ----------- TXRESETDONE_OUT : out std_logic; ------------------ Transmit Ports - pattern Generator Ports ---------------- TXPRBSSEL_IN : in std_logic_vector(2 downto 0) ); end uHTR_trigPD_GT; architecture RTL of uHTR_trigPD_GT is --**************************** Signal Declarations **************************** -- ground and tied_to_vcc_i signals signal tied_to_ground_i : std_logic; signal tied_to_ground_vec_i : std_logic_vector(63 downto 0); signal tied_to_vcc_i : std_logic; -- RX Datapath signals signal rxdata_i : std_logic_vector(63 downto 0); signal rxchariscomma_float_i : std_logic_vector(3 downto 0); signal rxcharisk_float_i : std_logic_vector(3 downto 0); signal rxdisperr_float_i : std_logic_vector(3 downto 0); signal rxnotintable_float_i : std_logic_vector(3 downto 0); signal rxrundisp_float_i : std_logic_vector(3 downto 0); -- TX Datapath signals signal txdata_i : std_logic_vector(63 downto 0); signal txkerr_float_i : std_logic_vector(3 downto 0); signal txrundisp_float_i : std_logic_vector(3 downto 0); signal rxstartofseq_float_i : std_logic; --******************************** Main Body of Code*************************** begin --------------------------- Static signal Assignments --------------------- tied_to_ground_i <= '0'; tied_to_ground_vec_i(63 downto 0) <= (others => '0'); tied_to_vcc_i <= '1'; ------------------- GT Datapath byte mapping ----------------- -- The GT provides little endian data (first byte received on RXDATA(7 downto 0)) RXDATA_OUT <= rxdata_i(31 downto 0); txdata_i <= (tied_to_ground_vec_i(31 downto 0) & TXDATA_IN); ----------------------------- GTXE2 Instance -------------------------- gtxe2_i :GTXE2_CHANNEL generic map ( --_______________________ Simulation-Only Attributes ___________________ SIM_RECEIVER_DETECT_PASS => ("TRUE"), SIM_RESET_SPEEDUP => (GT_SIM_GTRESET_SPEEDUP), SIM_TX_EIDLE_DRIVE_LEVEL => ("X"), SIM_CPLLREFCLK_SEL => ("001"), SIM_VERSION => ("4.0"), ------------------RX Byte and Word Alignment Attributes--------------- ALIGN_COMMA_DOUBLE => ("FALSE"), ALIGN_COMMA_ENABLE => ("1111111111"), ALIGN_COMMA_WORD => (4), ALIGN_MCOMMA_DET => ("TRUE"), ALIGN_MCOMMA_VALUE => ("1010000011"), ALIGN_PCOMMA_DET => ("TRUE"), ALIGN_PCOMMA_VALUE => ("0101111100"), SHOW_REALIGN_COMMA => ("TRUE"), RXSLIDE_AUTO_WAIT => (7), RXSLIDE_MODE => ("OFF"), RX_SIG_VALID_DLY => (10), ------------------RX 8B/10B Decoder Attributes--------------- RX_DISPERR_SEQ_MATCH => ("TRUE"), DEC_MCOMMA_DETECT => ("TRUE"), DEC_PCOMMA_DETECT => ("TRUE"), DEC_VALID_COMMA_ONLY => ("FALSE"), ------------------------RX Clock Correction Attributes---------------------- CBCC_DATA_SOURCE_SEL => ("DECODED"), CLK_COR_SEQ_2_USE => ("FALSE"), CLK_COR_KEEP_IDLE => ("FALSE"), CLK_COR_MAX_LAT => (20), CLK_COR_MIN_LAT => (16), CLK_COR_PRECEDENCE => ("TRUE"), CLK_COR_REPEAT_WAIT => (0), CLK_COR_SEQ_LEN => (1), CLK_COR_SEQ_1_ENABLE => ("1111"), CLK_COR_SEQ_1_1 => ("0100000000"), CLK_COR_SEQ_1_2 => ("0000000000"), CLK_COR_SEQ_1_3 => ("0000000000"), CLK_COR_SEQ_1_4 => ("0000000000"), CLK_CORRECT_USE => ("FALSE"), CLK_COR_SEQ_2_ENABLE => ("1111"), CLK_COR_SEQ_2_1 => ("0100000000"), CLK_COR_SEQ_2_2 => ("0000000000"), CLK_COR_SEQ_2_3 => ("0000000000"), CLK_COR_SEQ_2_4 => ("0000000000"), ------------------------RX Channel Bonding Attributes---------------------- CHAN_BOND_KEEP_ALIGN => ("FALSE"), CHAN_BOND_MAX_SKEW => (1), CHAN_BOND_SEQ_LEN => (1), CHAN_BOND_SEQ_1_1 => ("0000000000"), CHAN_BOND_SEQ_1_2 => ("0000000000"), CHAN_BOND_SEQ_1_3 => ("0000000000"), CHAN_BOND_SEQ_1_4 => ("0000000000"), CHAN_BOND_SEQ_1_ENABLE => ("1111"), CHAN_BOND_SEQ_2_1 => ("0000000000"), CHAN_BOND_SEQ_2_2 => ("0000000000"), CHAN_BOND_SEQ_2_3 => ("0000000000"), CHAN_BOND_SEQ_2_4 => ("0000000000"), CHAN_BOND_SEQ_2_ENABLE => ("1111"), CHAN_BOND_SEQ_2_USE => ("FALSE"), FTS_DESKEW_SEQ_ENABLE => ("1111"), FTS_LANE_DESKEW_CFG => ("1111"), FTS_LANE_DESKEW_EN => ("FALSE"), ---------------------------RX Margin Analysis Attributes---------------------------- ES_CONTROL => ("000000"), ES_ERRDET_EN => ("FALSE"), ES_EYE_SCAN_EN => ("TRUE"), ES_HORZ_OFFSET => (x"000"), ES_PMA_CFG => ("0000000000"), ES_PRESCALE => ("00000"), ES_QUALIFIER => (x"00000000000000000000"), ES_QUAL_MASK => (x"00000000000000000000"), ES_SDATA_MASK => (x"00000000000000000000"), ES_VERT_OFFSET => ("000000000"), -------------------------FPGA RX Interface Attributes------------------------- RX_DATA_WIDTH => (40), ---------------------------PMA Attributes---------------------------- OUTREFCLK_SEL_INV => ("11"), PMA_RSV => (PMA_RSV_IN), PMA_RSV2 => (x"2040"), PMA_RSV3 => ("00"), PMA_RSV4 => (x"00000000"), RX_BIAS_CFG => ("000000000100"), DMONITOR_CFG => (x"000A00"), RX_CM_SEL => ("00"), RX_CM_TRIM => ("000"), RX_DEBUG_CFG => ("000000000000"), RX_OS_CFG => ("0000010000000"), TERM_RCAL_CFG => ("10000"), TERM_RCAL_OVRD => ('0'), TST_RSV => (x"00000000"), RX_CLK25_DIV => (7), TX_CLK25_DIV => (7), UCODEER_CLR => ('0'), ---------------------------PCI Express Attributes---------------------------- PCS_PCIE_EN => ("FALSE"), ---------------------------PCS Attributes---------------------------- PCS_RSVD_ATTR => (PCS_RSVD_ATTR_IN), -------------RX Buffer Attributes------------ RXBUF_ADDR_MODE => ("FAST"), RXBUF_EIDLE_HI_CNT => ("1000"), RXBUF_EIDLE_LO_CNT => ("0000"), RXBUF_EN => ("TRUE"), RX_BUFFER_CFG => ("000000"), RXBUF_RESET_ON_CB_CHANGE => ("TRUE"), RXBUF_RESET_ON_COMMAALIGN => ("FALSE"), RXBUF_RESET_ON_EIDLE => ("FALSE"), RXBUF_RESET_ON_RATE_CHANGE => ("TRUE"), RXBUFRESET_TIME => ("00001"), RXBUF_THRESH_OVFLW => (61), RXBUF_THRESH_OVRD => ("FALSE"), RXBUF_THRESH_UNDFLW => (4), RXDLY_CFG => (x"001F"), RXDLY_LCFG => (x"030"), RXDLY_TAP_CFG => (x"0000"), RXPH_CFG => (x"000000"), RXPHDLY_CFG => (x"084020"), RXPH_MONITOR_SEL => ("00000"), RX_XCLK_SEL => ("RXREC"), RX_DDI_SEL => ("000000"), RX_DEFER_RESET_BUF_EN => ("TRUE"), -----------------------CDR Attributes------------------------- --For GTX only: Display Port, HBR/RBR- set RXCDR_CFG=72'h0380008bff40200008 --For GTX only: Display Port, HBR2 - set RXCDR_CFG=72'h038C008bff20200010 RXCDR_CFG => (x"03000023ff10200020"), RXCDR_FR_RESET_ON_EIDLE => ('0'), RXCDR_HOLD_DURING_EIDLE => ('0'), RXCDR_PH_RESET_ON_EIDLE => ('0'), RXCDR_LOCK_CFG => ("010101"), -------------------RX Initialization and Reset Attributes------------------- RXCDRFREQRESET_TIME => ("00001"), RXCDRPHRESET_TIME => ("00001"), RXISCANRESET_TIME => ("00001"), RXPCSRESET_TIME => ("00001"), RXPMARESET_TIME => ("00011"), -------------------RX OOB Signaling Attributes------------------- RXOOB_CFG => ("0000110"), -------------------------RX Gearbox Attributes--------------------------- RXGEARBOX_EN => ("FALSE"), GEARBOX_MODE => ("000"), -------------------------PRBS Detection Attribute----------------------- RXPRBS_ERR_LOOPBACK => ('0'), -------------Power-Down Attributes---------- PD_TRANS_TIME_FROM_P2 => (x"03c"), PD_TRANS_TIME_NONE_P2 => (x"3c"), PD_TRANS_TIME_TO_P2 => (x"64"), -------------RX OOB Signaling Attributes---------- SAS_MAX_COM => (64), SAS_MIN_COM => (36), SATA_BURST_SEQ_LEN => ("1111"), SATA_BURST_VAL => ("100"), SATA_EIDLE_VAL => ("100"), SATA_MAX_BURST => (8), SATA_MAX_INIT => (21), SATA_MAX_WAKE => (7), SATA_MIN_BURST => (4), SATA_MIN_INIT => (12), SATA_MIN_WAKE => (4), -------------RX Fabric Clock Output Control Attributes---------- TRANS_TIME_RATE => (x"0E"), --------------TX Buffer Attributes---------------- TXBUF_EN => ("TRUE"), TXBUF_RESET_ON_RATE_CHANGE => ("TRUE"), TXDLY_CFG => (x"001F"), TXDLY_LCFG => (x"030"), TXDLY_TAP_CFG => (x"0000"), TXPH_CFG => (x"0780"), TXPHDLY_CFG => (x"084020"), TXPH_MONITOR_SEL => ("00000"), TX_XCLK_SEL => ("TXOUT"), -------------------------FPGA TX Interface Attributes------------------------- TX_DATA_WIDTH => (40), -------------------------TX Configurable Driver Attributes------------------------- TX_DEEMPH0 => ("00000"), TX_DEEMPH1 => ("00000"), TX_EIDLE_ASSERT_DELAY => ("110"), TX_EIDLE_DEASSERT_DELAY => ("100"), TX_LOOPBACK_DRIVE_HIZ => ("FALSE"), TX_MAINCURSOR_SEL => ('0'), TX_DRIVE_MODE => ("DIRECT"), TX_MARGIN_FULL_0 => ("1001110"), TX_MARGIN_FULL_1 => ("1001001"), TX_MARGIN_FULL_2 => ("1000101"), TX_MARGIN_FULL_3 => ("1000010"), TX_MARGIN_FULL_4 => ("1000000"), TX_MARGIN_LOW_0 => ("1000110"), TX_MARGIN_LOW_1 => ("1000100"), TX_MARGIN_LOW_2 => ("1000010"), TX_MARGIN_LOW_3 => ("1000000"), TX_MARGIN_LOW_4 => ("1000000"), -------------------------TX Gearbox Attributes-------------------------- TXGEARBOX_EN => ("FALSE"), -------------------------TX Initialization and Reset Attributes-------------------------- TXPCSRESET_TIME => ("00001"), TXPMARESET_TIME => ("00001"), -------------------------TX Receiver Detection Attributes-------------------------- TX_RXDETECT_CFG => (x"1832"), TX_RXDETECT_REF => ("100"), ----------------------------CPLL Attributes---------------------------- CPLL_CFG => (x"BC07DC"), CPLL_FBDIV => (2), CPLL_FBDIV_45 => (5), CPLL_INIT_CFG => (x"00001E"), CPLL_LOCK_CFG => (x"01E8"), CPLL_REFCLK_DIV => (1), RXOUT_DIV => (2), TXOUT_DIV => (2), SATA_CPLL_CFG => ("VCO_3000MHZ"), --------------RX Initialization and Reset Attributes------------- RXDFELPMRESET_TIME => ("0001111"), --------------RX Equalizer Attributes------------- RXLPM_HF_CFG => ("00000011110000"), RXLPM_LF_CFG => ("00000011110000"), RX_DFE_GAIN_CFG => (x"020FEA"), RX_DFE_H2_CFG => ("000000000000"), RX_DFE_H3_CFG => ("000001000000"), RX_DFE_H4_CFG => ("00011110000"), RX_DFE_H5_CFG => ("00011100000"), RX_DFE_KL_CFG => ("0000011111110"), RX_DFE_LPM_CFG => (x"0904"), RX_DFE_LPM_HOLD_DURING_EIDLE => ('0'), RX_DFE_UT_CFG => ("10001111000000000"), RX_DFE_VP_CFG => ("00011111100000011"), -------------------------Power-Down Attributes------------------------- RX_CLKMUX_PD => ('1'), TX_CLKMUX_PD => ('1'), -------------------------FPGA RX Interface Attribute------------------------- RX_INT_DATAWIDTH => (1), -------------------------FPGA TX Interface Attribute------------------------- TX_INT_DATAWIDTH => (1), ------------------TX Configurable Driver Attributes--------------- TX_QPI_STATUS_EN => ('0'), -------------------------RX Equalizer Attributes-------------------------- RX_DFE_KL_CFG2 => (RX_DFE_KL_CFG2_IN), RX_DFE_XYD_CFG => ("0000000000000"), -------------------------TX Configurable Driver Attributes-------------------------- TX_PREDRIVER_MODE => ('0') ) port map ( --------------------------------- CPLL Ports ------------------------------- CPLLFBCLKLOST => CPLLFBCLKLOST_OUT, CPLLLOCK => CPLLLOCK_OUT, CPLLLOCKDETCLK => CPLLLOCKDETCLK_IN, CPLLLOCKEN => tied_to_vcc_i, CPLLPD => tied_to_ground_i, CPLLREFCLKLOST => CPLLREFCLKLOST_OUT, CPLLREFCLKSEL => "001", CPLLRESET => CPLLRESET_IN, GTRSVD => "0000000000000000", PCSRSVDIN => "0000000000000000", PCSRSVDIN2 => "00000", PMARSVDIN => "00000", PMARSVDIN2 => "00000", TSTIN => "11111111111111111111", TSTOUT => open, ---------------------------------- Channel --------------------------------- CLKRSVD => "0000", -------------------------- Channel - Clocking Ports ------------------------ GTGREFCLK => tied_to_ground_i, GTNORTHREFCLK0 => tied_to_ground_i, GTNORTHREFCLK1 => tied_to_ground_i, GTREFCLK0 => GTREFCLK0_IN, GTREFCLK1 => tied_to_ground_i, GTSOUTHREFCLK0 => tied_to_ground_i, GTSOUTHREFCLK1 => tied_to_ground_i, ---------------------------- Channel - DRP Ports -------------------------- DRPADDR => DRPADDR_IN, DRPCLK => DRPCLK_IN, DRPDI => DRPDI_IN, DRPDO => DRPDO_OUT, DRPEN => DRPEN_IN, DRPRDY => DRPRDY_OUT, DRPWE => DRPWE_IN, ------------------------------- Clocking Ports ----------------------------- GTREFCLKMONITOR => open, QPLLCLK => QPLLCLK_IN, QPLLREFCLK => QPLLREFCLK_IN, RXSYSCLKSEL => "00", TXSYSCLKSEL => "00", --------------------------- Digital Monitor Ports -------------------------- DMONITOROUT => open, ----------------- FPGA TX Interface Datapath Configuration ---------------- TX8B10BEN => tied_to_vcc_i, ------------------------------- Loopback Ports ----------------------------- LOOPBACK => tied_to_ground_vec_i(2 downto 0), ----------------------------- PCI Express Ports ---------------------------- PHYSTATUS => open, RXRATE => tied_to_ground_vec_i(2 downto 0), RXVALID => open, ------------------------------ Power-Down Ports ---------------------------- RXPD => RXPD_IN, TXPD => TXPD_IN, -------------------------- RX 8B/10B Decoder Ports ------------------------- SETERRSTATUS => tied_to_ground_i, --------------------- RX Initialization and Reset Ports -------------------- EYESCANRESET => tied_to_ground_i, RXUSERRDY => RXUSERRDY_IN, -------------------------- RX Margin Analysis Ports ------------------------ EYESCANDATAERROR => EYESCANDATAERROR_OUT, EYESCANMODE => tied_to_ground_i, EYESCANTRIGGER => tied_to_ground_i, ------------------------- Receive Ports - CDR Ports ------------------------ RXCDRFREQRESET => tied_to_ground_i, RXCDRHOLD => tied_to_ground_i, RXCDRLOCK => RXCDRLOCK_OUT, RXCDROVRDEN => tied_to_ground_i, RXCDRRESET => tied_to_ground_i, RXCDRRESETRSV => tied_to_ground_i, ------------------- Receive Ports - Clock Correction Ports ----------------- RXCLKCORCNT => open, ---------- Receive Ports - FPGA RX Interface Datapath Configuration -------- RX8B10BEN => tied_to_vcc_i, ------------------ Receive Ports - FPGA RX Interface Ports ----------------- RXUSRCLK => RXUSRCLK_IN, RXUSRCLK2 => RXUSRCLK2_IN, ------------------ Receive Ports - FPGA RX interface Ports ----------------- RXDATA => rxdata_i, ------------------- Receive Ports - Pattern Checker Ports ------------------ RXPRBSERR => RXPRBSERR_OUT, RXPRBSSEL => RXPRBSSEL_IN, ------------------- Receive Ports - Pattern Checker ports ------------------ RXPRBSCNTRESET => RXPRBSCNTRESET_IN, -------------------- Receive Ports - RX Equalizer Ports ------------------- RXDFEXYDEN => tied_to_vcc_i, RXDFEXYDHOLD => tied_to_ground_i, RXDFEXYDOVRDEN => tied_to_ground_i, ------------------ Receive Ports - RX 8B/10B Decoder Ports ----------------- RXDISPERR(7 downto 4) => rxdisperr_float_i, RXDISPERR(3 downto 0) => RXDISPERR_OUT, RXNOTINTABLE(7 downto 4) => rxnotintable_float_i, RXNOTINTABLE(3 downto 0) => RXNOTINTABLE_OUT, --------------------------- Receive Ports - RX AFE ------------------------- GTXRXP => GTXRXP_IN, ------------------------ Receive Ports - RX AFE Ports ---------------------- GTXRXN => GTXRXN_IN, ------------------- Receive Ports - RX Buffer Bypass Ports ----------------- RXBUFRESET => tied_to_ground_i, RXBUFSTATUS => open, RXDDIEN => tied_to_ground_i, RXDLYBYPASS => tied_to_vcc_i, RXDLYEN => tied_to_ground_i, RXDLYOVRDEN => tied_to_ground_i, RXDLYSRESET => tied_to_ground_i, RXDLYSRESETDONE => open, RXPHALIGN => tied_to_ground_i, RXPHALIGNDONE => open, RXPHALIGNEN => tied_to_ground_i, RXPHDLYPD => tied_to_ground_i, RXPHDLYRESET => tied_to_ground_i, RXPHMONITOR => open, RXPHOVRDEN => tied_to_ground_i, RXPHSLIPMONITOR => open, RXSTATUS => open, -------------- Receive Ports - RX Byte and Word Alignment Ports ------------ RXBYTEISALIGNED => open, RXBYTEREALIGN => open, RXCOMMADET => open, RXCOMMADETEN => tied_to_vcc_i, RXMCOMMAALIGNEN => tied_to_vcc_i, RXPCOMMAALIGNEN => tied_to_vcc_i, ------------------ Receive Ports - RX Channel Bonding Ports ---------------- RXCHANBONDSEQ => open, RXCHBONDEN => tied_to_ground_i, RXCHBONDLEVEL => tied_to_ground_vec_i(2 downto 0), RXCHBONDMASTER => tied_to_ground_i, RXCHBONDO => open, RXCHBONDSLAVE => tied_to_ground_i, ----------------- Receive Ports - RX Channel Bonding Ports ---------------- RXCHANISALIGNED => open, RXCHANREALIGN => open, -------------------- Receive Ports - RX Equailizer Ports ------------------- RXLPMHFHOLD => RXLPMHFHOLD_IN, RXLPMHFOVRDEN => tied_to_ground_i, RXLPMLFHOLD => RXLPMLFHOLD_IN, --------------------- Receive Ports - RX Equalizer Ports ------------------- RXDFEAGCHOLD => tied_to_ground_i, RXDFEAGCOVRDEN => tied_to_ground_i, RXDFECM1EN => tied_to_ground_i, RXDFELFHOLD => tied_to_ground_i, RXDFELFOVRDEN => tied_to_ground_i, RXDFELPMRESET => tied_to_ground_i, RXDFETAP2HOLD => tied_to_ground_i, RXDFETAP2OVRDEN => tied_to_ground_i, RXDFETAP3HOLD => tied_to_ground_i, RXDFETAP3OVRDEN => tied_to_ground_i, RXDFETAP4HOLD => tied_to_ground_i, RXDFETAP4OVRDEN => tied_to_ground_i, RXDFETAP5HOLD => tied_to_ground_i, RXDFETAP5OVRDEN => tied_to_ground_i, RXDFEUTHOLD => tied_to_ground_i, RXDFEUTOVRDEN => tied_to_ground_i, RXDFEVPHOLD => tied_to_ground_i, RXDFEVPOVRDEN => tied_to_ground_i, RXDFEVSEN => tied_to_ground_i, RXLPMLFKLOVRDEN => tied_to_ground_i, RXMONITOROUT => open, RXMONITORSEL => "00", RXOSHOLD => tied_to_ground_i, RXOSOVRDEN => tied_to_ground_i, ------------ Receive Ports - RX Fabric ClocK Output Control Ports ---------- RXRATEDONE => open, --------------- Receive Ports - RX Fabric Output Control Ports ------------- RXOUTCLK => RXOUTCLK_OUT, RXOUTCLKFABRIC => open, RXOUTCLKPCS => open, RXOUTCLKSEL => "010", ---------------------- Receive Ports - RX Gearbox Ports -------------------- RXDATAVALID => open, RXHEADER => open, RXHEADERVALID => open, RXSTARTOFSEQ => open, --------------------- Receive Ports - RX Gearbox Ports -------------------- RXGEARBOXSLIP => tied_to_ground_i, ------------- Receive Ports - RX Initialization and Reset Ports ------------ GTRXRESET => GTRXRESET_IN, RXOOBRESET => tied_to_ground_i, RXPCSRESET => tied_to_ground_i, RXPMARESET => RXPMARESET_IN, ------------------ Receive Ports - RX Margin Analysis ports ---------------- RXLPMEN => tied_to_vcc_i, ------------------- Receive Ports - RX OOB Signaling ports ----------------- RXCOMSASDET => open, RXCOMWAKEDET => open, ------------------ Receive Ports - RX OOB Signaling ports ----------------- RXCOMINITDET => open, ------------------ Receive Ports - RX OOB signalling Ports ----------------- RXELECIDLE => open, RXELECIDLEMODE => "11", ----------------- Receive Ports - RX Polarity Control Ports ---------------- RXPOLARITY => tied_to_ground_i, ---------------------- Receive Ports - RX gearbox ports -------------------- RXSLIDE => tied_to_ground_i, ------------------- Receive Ports - RX8B/10B Decoder Ports ----------------- RXCHARISCOMMA => open, RXCHARISK(7 downto 4) => rxcharisk_float_i, RXCHARISK(3 downto 0) => RXCHARISK_OUT, ------------------ Receive Ports - Rx Channel Bonding Ports ---------------- RXCHBONDI => "00000", -------------- Receive Ports -RX Initialization and Reset Ports ------------ RXRESETDONE => RXRESETDONE_OUT, -------------------------------- Rx AFE Ports ------------------------------ RXQPIEN => tied_to_ground_i, RXQPISENN => open, RXQPISENP => open, --------------------------- TX Buffer Bypass Ports ------------------------- TXPHDLYTSTCLK => tied_to_ground_i, ------------------------ TX Configurable Driver Ports ---------------------- TXPOSTCURSOR => "00000", TXPOSTCURSORINV => tied_to_ground_i, TXPRECURSOR => tied_to_ground_vec_i(4 downto 0), TXPRECURSORINV => tied_to_ground_i, TXQPIBIASEN => tied_to_ground_i, TXQPISTRONGPDOWN => tied_to_ground_i, TXQPIWEAKPUP => tied_to_ground_i, --------------------- TX Initialization and Reset Ports -------------------- CFGRESET => tied_to_ground_i, GTTXRESET => GTTXRESET_IN, PCSRSVDOUT => open, TXUSERRDY => TXUSERRDY_IN, ---------------------- Transceiver Reset Mode Operation -------------------- GTRESETSEL => tied_to_ground_i, RESETOVRD => tied_to_ground_i, ---------------- Transmit Ports - 8b10b Encoder Control Ports -------------- TXCHARDISPMODE => tied_to_ground_vec_i(7 downto 0), TXCHARDISPVAL => tied_to_ground_vec_i(7 downto 0), ------------------ Transmit Ports - FPGA TX Interface Ports ---------------- TXUSRCLK => TXUSRCLK_IN, TXUSRCLK2 => TXUSRCLK2_IN, --------------------- Transmit Ports - PCI Express Ports ------------------- TXELECIDLE => tied_to_ground_i, TXMARGIN => tied_to_ground_vec_i(2 downto 0), TXRATE => tied_to_ground_vec_i(2 downto 0), TXSWING => tied_to_ground_i, ------------------ Transmit Ports - Pattern Generator Ports ---------------- TXPRBSFORCEERR => tied_to_ground_i, ------------------ Transmit Ports - TX Buffer Bypass Ports ----------------- TXDLYBYPASS => tied_to_vcc_i, TXDLYEN => tied_to_ground_i, TXDLYHOLD => tied_to_ground_i, TXDLYOVRDEN => tied_to_ground_i, TXDLYSRESET => tied_to_ground_i, TXDLYSRESETDONE => open, TXDLYUPDOWN => tied_to_ground_i, TXPHALIGN => tied_to_ground_i, TXPHALIGNDONE => open, TXPHALIGNEN => tied_to_ground_i, TXPHDLYPD => tied_to_ground_i, TXPHDLYRESET => tied_to_ground_i, TXPHINIT => tied_to_ground_i, TXPHINITDONE => open, TXPHOVRDEN => tied_to_ground_i, ---------------------- Transmit Ports - TX Buffer Ports -------------------- TXBUFSTATUS => open, --------------- Transmit Ports - TX Configurable Driver Ports -------------- TXBUFDIFFCTRL => "100", TXDEEMPH => tied_to_ground_i, TXDIFFCTRL => "1000", TXDIFFPD => tied_to_ground_i, TXINHIBIT => tied_to_ground_i, TXMAINCURSOR => "0000000", TXPISOPD => tied_to_ground_i, ------------------ Transmit Ports - TX Data Path interface ----------------- TXDATA => txdata_i, ---------------- Transmit Ports - TX Driver and OOB signaling -------------- GTXTXN => GTXTXN_OUT, GTXTXP => GTXTXP_OUT, ----------- Transmit Ports - TX Fabric Clock Output Control Ports ---------- TXOUTCLK => TXOUTCLK_OUT, TXOUTCLKFABRIC => TXOUTCLKFABRIC_OUT, TXOUTCLKPCS => TXOUTCLKPCS_OUT, TXOUTCLKSEL => "010", TXRATEDONE => open, --------------------- Transmit Ports - TX Gearbox Ports -------------------- TXCHARISK(7 downto 4) => tied_to_ground_vec_i(3 downto 0), TXCHARISK(3 downto 0) => TXCHARISK_IN, TXGEARBOXREADY => open, TXHEADER => tied_to_ground_vec_i(2 downto 0), TXSEQUENCE => tied_to_ground_vec_i(6 downto 0), TXSTARTSEQ => tied_to_ground_i, ------------- Transmit Ports - TX Initialization and Reset Ports ----------- TXPCSRESET => tied_to_ground_i, TXPMARESET => tied_to_ground_i, TXRESETDONE => TXRESETDONE_OUT, ------------------ Transmit Ports - TX OOB signalling Ports ---------------- TXCOMFINISH => open, TXCOMINIT => tied_to_ground_i, TXCOMSAS => tied_to_ground_i, TXCOMWAKE => tied_to_ground_i, TXPDELECIDLEMODE => tied_to_ground_i, ----------------- Transmit Ports - TX Polarity Control Ports --------------- TXPOLARITY => tied_to_ground_i, --------------- Transmit Ports - TX Receiver Detection Ports -------------- TXDETECTRX => tied_to_ground_i, ------------------ Transmit Ports - TX8b/10b Encoder Ports ----------------- TX8B10BBYPASS => tied_to_ground_vec_i(7 downto 0), ------------------ Transmit Ports - pattern Generator Ports ---------------- TXPRBSSEL => TXPRBSSEL_IN, ----------------------- Tx Configurable Driver Ports ---------------------- TXQPISENN => open, TXQPISENP => open ); end RTL;