serdes5gpdprod_tx_startup_fsm.vhd

--////////////////////////////////////////////////////////////////////////////////
--//   ____  ____ 
--//  /   /\/   / 
--// /___/  \  /    Vendor: Xilinx 
--// \   \   \/     Version : 2.7
--//  \   \         Application : 7 Series FPGAs Transceivers Wizard 
--//  /   /         Filename :serdes5gpdprod_tx_startup_fsm.vhd
--// /___/   /\     
--// \   \  /  \ 
--//  \___\/\___\ 
--//
--//
--  Description :     This module performs TX reset and initialization.
--                     
--
--
-- Module serdes5GpdProd_tx_startup_fsm
-- Generated by Xilinx 7 Series FPGAs Transceivers Wizard
-- 
-- 
-- (c) Copyright 2010-2012 Xilinx, Inc. All rights reserved.
-- 
-- This file contains confidential and proprietary information
-- of Xilinx, Inc. and is protected under U.S. and
-- international copyright and other intellectual property
-- laws.
-- 
-- DISCLAIMER
-- This disclaimer is not a license and does not grant any
-- rights to the materials distributed herewith. Except as
-- otherwise provided in a valid license issued to you by
-- Xilinx, and to the maximum extent permitted by applicable
-- law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
-- WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
-- AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
-- BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
-- INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
-- (2) Xilinx shall not be liable (whether in contract or tort,
-- including negligence, or under any other theory of
-- liability) for any loss or damage of any kind or nature
-- related to, arising under or in connection with these
-- materials, including for any direct, or any indirect,
-- special, incidental, or consequential loss or damage
-- (including loss of data, profits, goodwill, or any type of
-- loss or damage suffered as a result of any action brought
-- by a third party) even if such damage or loss was
-- reasonably foreseeable or Xilinx had been advised of the
-- possibility of the same.
-- 
-- CRITICAL APPLICATIONS
-- Xilinx products are not designed or intended to be fail-
-- safe, or for use in any application requiring fail-safe
-- performance, such as life-support or safety devices or
-- systems, Class III medical devices, nuclear facilities,
-- applications related to the deployment of airbags, or any
-- other applications that could lead to death, personal
-- injury, or severe property or environmental damage
-- (individually and collectively, "Critical
-- Applications"). Customer assumes the sole risk and
-- liability of any use of Xilinx products in Critical
-- Applications, subject only to applicable laws and
-- regulations governing limitations on product liability.
-- 
-- THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
-- PART OF THIS FILE AT ALL TIMES. 


--*****************************************************************************

library IEEE;
use IEEE.STD_LOGIC_1164.ALL;
use IEEE.NUMERIC_STD.ALL;

entity serdes5GpdProd_TX_STARTUP_FSM is
  Generic( GT_TYPE                  : string  := "GTX";
           STABLE_CLOCK_PERIOD      : integer range 4 to 250 := 8; --Period of the stable clock driving this state-machine, unit is [ns]
           RETRY_COUNTER_BITWIDTH   : integer range 2 to 8  := 8; 
           TX_QPLL_USED             : boolean := False;           -- the TX and RX Reset FSMs must
           RX_QPLL_USED             : boolean := False;           -- share these two generic values
           PHASE_ALIGNMENT_MANUAL   : boolean := True             -- Decision if a manual phase-alignment is necessary or the automatic 
                                                                  -- is enough. For single-lane applications the automatic alignment is 
                                                                  -- sufficient              
         );     
    Port ( STABLE_CLOCK             : in  STD_LOGIC;              --Stable Clock, either a stable clock from the PCB
                                                                  --or reference-clock present at startup.
           TXUSERCLK                : in  STD_LOGIC;              --TXUSERCLK as used in the design
           SOFT_RESET               : in  STD_LOGIC;              --User Reset, can be pulled any time
           QPLLREFCLKLOST           : in  STD_LOGIC;              --QPLL Reference-clock for the GT is lost
           CPLLREFCLKLOST           : in  STD_LOGIC;              --CPLL Reference-clock for the GT is lost
           QPLLLOCK                 : in  STD_LOGIC;              --Lock Detect from the QPLL of the GT
           CPLLLOCK                 : in  STD_LOGIC;              --Lock Detect from the CPLL of the GT
           TXRESETDONE              : in  STD_LOGIC;      
           MMCM_LOCK                : in  STD_LOGIC;      
           GTTXRESET                : out STD_LOGIC:='0';      
           MMCM_RESET               : out STD_LOGIC:='1';      
           QPLL_RESET               : out STD_LOGIC:='0';        --Reset QPLL
           CPLL_RESET               : out STD_LOGIC:='0';        --Reset CPLL
           TX_FSM_RESET_DONE        : out STD_LOGIC;             --Reset-sequence has sucessfully been finished.
           TXUSERRDY                : out STD_LOGIC:='0';
           RUN_PHALIGNMENT          : out STD_LOGIC:='0';
           RESET_PHALIGNMENT        : out STD_LOGIC:='0';
           PHALIGNMENT_DONE         : in  STD_LOGIC;
           
           RETRY_COUNTER            : out  STD_LOGIC_VECTOR (RETRY_COUNTER_BITWIDTH-1 downto 0):=(others=>'0')-- Number of 
                                                            -- Retries it took to get the transceiver up and running
           );
end serdes5GpdProd_TX_STARTUP_FSM;

--Interdependencies:
-- * Timing depends on the frequency of the stable clock. Hence counters-sizes
--   are calculated at design-time based on the Generics
--   
-- * if either of PLLs is reset during TX-startup, it does not need to be reset again by RX
--   => signal which PLL has been reset
-- * 



architecture RTL of serdes5GpdProd_TX_STARTUP_FSM is

  component serdes5GpdProd_sync_block
   generic (
     INITIALISE : bit_vector(1 downto 0) := "00"
   );
   port  (
             clk           : in  std_logic;
             data_in       : in  std_logic;
             data_out      : out std_logic
          );
   end component;

  type tx_rst_fsm_type is(
    INIT, ASSERT_ALL_RESETS, RELEASE_PLL_RESET,
    RELEASE_MMCM_RESET, WAIT_RESET_DONE, DO_PHASE_ALIGNMENT,
    RESET_FSM_DONE);
    
  signal tx_state : tx_rst_fsm_type := INIT;

  constant MMCM_LOCK_CNT_MAX    : integer := 1024;
  constant STARTUP_DELAY        : integer := 500;--AR43482: Transceiver needs to wait for 500 ns after configuration
  constant WAIT_CYCLES          : integer := STARTUP_DELAY / STABLE_CLOCK_PERIOD; -- Number of Clock-Cycles to wait after configuration
  constant WAIT_MAX             : integer := WAIT_CYCLES + 10;                    -- 500 ns plus some additional margin
    
  constant WAIT_TIMEOUT_2ms     : integer := 2000000 / STABLE_CLOCK_PERIOD;--  2 ms time-out
  constant WAIT_TLOCK_MAX       : integer :=  100000 / STABLE_CLOCK_PERIOD;--100 us time-out
  constant WAIT_TIMEOUT_500us   : integer :=  500000 / STABLE_CLOCK_PERIOD;--100 us time-out
    
  signal init_wait_count        : integer range 0 to WAIT_MAX:=0;
  signal init_wait_done         : std_logic := '0';
  signal pll_reset_asserted     : std_logic := '0';

  signal tx_fsm_reset_done_int     : std_logic := '0';
  signal tx_fsm_reset_done_int_s2  : std_logic := '0';
  signal tx_fsm_reset_done_int_s3  : std_logic := '0';
   
  signal txresetdone_s2         : std_logic := '0'; 
  signal txresetdone_s3         : std_logic := '0'; 

  constant MAX_RETRIES          : integer := 2**RETRY_COUNTER_BITWIDTH-1; 
  signal retry_counter_int      : integer range 0 to MAX_RETRIES;  
  signal time_out_counter       : integer range 0 to WAIT_TIMEOUT_2ms := 0;
    
  signal reset_time_out         : std_logic := '0';
  signal time_out_2ms           : std_logic := '0';--\Flags that the various time-out points 
  signal time_tlock_max         : std_logic := '0';--|have been reached.
  signal time_out_500us         : std_logic := '0';--/
    
  signal mmcm_lock_count        : integer range 0 to MMCM_LOCK_CNT_MAX-1:=0;
  signal mmcm_lock_int          : std_logic := '0';
  signal mmcm_lock_i            : std_logic := '0';
  signal mmcm_lock_reclocked    : std_logic := '0';
    
  signal run_phase_alignment_int    : std_logic := '0';
  signal run_phase_alignment_int_s2 : std_logic := '0';
  signal run_phase_alignment_int_s3 : std_logic := '0';
  constant MAX_WAIT_BYPASS      : integer := 173568; --110000 TXUSRCLK cycles is the max time for Multi lane designs
 


  signal wait_bypass_count      : integer range 0 to MAX_WAIT_BYPASS-1;
  signal time_out_wait_bypass   : std_logic := '0';
  signal time_out_wait_bypass_s2   : std_logic := '0';
  signal time_out_wait_bypass_s3   : std_logic := '0';
  signal refclk_lost            : std_logic;

   signal      cplllock_sync: std_logic := '0';
  signal      qplllock_sync: std_logic := '0';
  signal      cplllock_prev: std_logic := '0';
  signal      qplllock_prev: std_logic := '0';
  signal      cplllock_ris_edge: std_logic := '0';
  signal      qplllock_ris_edge: std_logic := '0';
 
begin
  --Alias section, signals used within this module mapped to output ports:
  RETRY_COUNTER     <= STD_LOGIC_VECTOR(TO_UNSIGNED(retry_counter_int,RETRY_COUNTER_BITWIDTH));
  RUN_PHALIGNMENT   <= run_phase_alignment_int;
  TX_FSM_RESET_DONE <= tx_fsm_reset_done_int;    

  process(STABLE_CLOCK)
  begin
    if rising_edge(STABLE_CLOCK) then
      -- The counter starts running when configuration has finished and 
      -- the clock is stable. When its maximum count-value has been reached,
      -- the 500 ns from Answer Record 43482 have been passed.
      if init_wait_count = WAIT_MAX then
        init_wait_done <= '1';
      else
        init_wait_count <= init_wait_count + 1;
      end if;
    end if;
  end process;


  timeouts:process(STABLE_CLOCK)
  begin
    if rising_edge(STABLE_CLOCK) then
      -- One common large counter for generating three time-out signals.
      -- Intermediate time-outs are derived from calculated values, based
      -- on the period of the provided clock.
      if reset_time_out = '1' then
        time_out_counter  <= 0;
        time_out_2ms      <= '0';
        time_tlock_max    <= '0';
        time_out_500us    <= '0';
      else
        if time_out_counter = WAIT_TIMEOUT_2ms then
          time_out_2ms <= '1';
        else
          time_out_counter <= time_out_counter + 1;
        end if;
        
        if time_out_counter = WAIT_TLOCK_MAX then
          time_tlock_max <= '1';
        end if;
      
        if time_out_counter = WAIT_TIMEOUT_500us then
          time_out_500us <= '1';
        end if;
      end if;
    end if;
  end process;

  mmcm_lock_wait:process(STABLE_CLOCK)
  begin
    if rising_edge(STABLE_CLOCK) then
      if mmcm_lock_i = '0' then
        mmcm_lock_count <= 0;
        mmcm_lock_reclocked   <= '0';
      else 
        if mmcm_lock_count < MMCM_LOCK_CNT_MAX - 1 then
          mmcm_lock_count <= mmcm_lock_count + 1;
        else
          mmcm_lock_reclocked <= '1';
        end if;
      end if;
    end if;
  end process;
  


  -- Clock Domain Crossing

  sync_run_phase_alignment_int : serdes5GpdProd_sync_block
  port map
         (
            clk              =>  TXUSERCLK,
            data_in          =>  run_phase_alignment_int ,
            data_out         =>  run_phase_alignment_int_s2  
         );

  sync_tx_fsm_reset_done_int : serdes5GpdProd_sync_block
  port map
         (
            clk              =>  TXUSERCLK,
            data_in          =>  tx_fsm_reset_done_int,
            data_out         =>  tx_fsm_reset_done_int_s2  
         );

  process(TXUSERCLK)
  begin
    if rising_edge(TXUSERCLK) then
      run_phase_alignment_int_s3   <=  run_phase_alignment_int_s2;

      tx_fsm_reset_done_int_s3     <=  tx_fsm_reset_done_int_s2;
    end if;
  end process;

 sync_TXRESETDONE : serdes5GpdProd_sync_block
  port map
         (
            clk              =>  STABLE_CLOCK,
            data_in          =>  TXRESETDONE,
            data_out         =>  txresetdone_s2 
         );

  sync_time_out_wait_bypass : serdes5GpdProd_sync_block
  port map
         (
            clk              =>  STABLE_CLOCK,
            data_in          =>  time_out_wait_bypass,
            data_out         =>  time_out_wait_bypass_s2  
         );

  sync_mmcm_lock_reclocked : serdes5GpdProd_sync_block
  port map
         (
            clk              =>  STABLE_CLOCK,
            data_in          =>  MMCM_LOCK,
            data_out         =>  mmcm_lock_i 
         );

  process(STABLE_CLOCK)
  begin
    if rising_edge(STABLE_CLOCK) then
       txresetdone_s3     <= txresetdone_s2;

       time_out_wait_bypass_s3 <=  time_out_wait_bypass_s2;
       cplllock_prev           <=  cplllock_sync;
       qplllock_prev           <=  qplllock_sync;
    end if;
  end process;

 sync_CPLLLOCK : serdes5GpdProd_sync_block
  port map
         (
            clk              =>  STABLE_CLOCK,
            data_in          =>  CPLLLOCK,
            data_out         =>  cplllock_sync 
         );

 sync_QPLLLOCK : serdes5GpdProd_sync_block
  port map
         (
            clk              =>  STABLE_CLOCK,
            data_in          =>  QPLLLOCK,
            data_out         =>  qplllock_sync 
         );


  process (STABLE_CLOCK)
  begin
    if rising_edge(STABLE_CLOCK) then
     if(SOFT_RESET = '1' ) then
       cplllock_ris_edge <= '0';
     elsif((cplllock_prev = '0') and (cplllock_sync = '1')) then
       cplllock_ris_edge <= '1';
     elsif(tx_state = ASSERT_ALL_RESETS or tx_state = RELEASE_PLL_RESET) then
       cplllock_ris_edge <= cplllock_ris_edge;
     else 
       cplllock_ris_edge <= '0';
     end if;
    end if;
  end process;

  process (STABLE_CLOCK)
  begin
    if rising_edge(STABLE_CLOCK) then
     if(SOFT_RESET = '1' ) then
       qplllock_ris_edge <= '0';
     elsif((qplllock_prev = '0') and (qplllock_sync = '1')) then
       qplllock_ris_edge <= '1';
     elsif(tx_state = ASSERT_ALL_RESETS or tx_state = RELEASE_PLL_RESET) then
       qplllock_ris_edge <= qplllock_ris_edge;
     else 
       qplllock_ris_edge <= '0';
     end if;
    end if;
  end process;


  timeout_buffer_bypass:process(TXUSERCLK)
  begin
    if rising_edge(TXUSERCLK) then
      if run_phase_alignment_int_s3 = '0' then
        wait_bypass_count     <= 0;
        time_out_wait_bypass  <= '0';
      elsif (run_phase_alignment_int_s3 = '1') and (tx_fsm_reset_done_int_s3 = '0')  then
        if wait_bypass_count = MAX_WAIT_BYPASS - 1 then
          time_out_wait_bypass <= '1';
        else
          wait_bypass_count <= wait_bypass_count + 1;
        end if;
      end if;
    end if;
  end process;

    refclk_lost <= '1' when ((TX_QPLL_USED and QPLLREFCLKLOST='1') or (not TX_QPLL_USED and CPLLREFCLKLOST='1')) else '0';


  --FSM for resetting the GTX/GTH/GTP in the 7-series. 
  --~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
  --
  -- Following steps are performed:
  -- 1) Only for GTX - After configuration wait for approximately 500 ns as specified in 
  --    answer-record 43482
  -- 2) Assert all resets on the GT and on an MMCM potentially connected. 
  --    After that wait until a reference-clock has been detected.
  -- 3) Release the reset to the GT and wait until the GT-PLL has locked.
  -- 4) Release the MMCM-reset and wait until the MMCM has signalled lock.
  --    Also signal to the RX-side which PLL has been reset.
  -- 5) Wait for the RESET_DONE-signal from the GT.
  -- 6) Signal to start the phase-alignment procedure and wait for it to 
  --    finish.
  -- 7) Reset-sequence has successfully run through. Signal this to the 
  --    rest of the design by asserting TX_FSM_RESET_DONE.
  
  reset_fsm:process(STABLE_CLOCK)
  begin
    if rising_edge(STABLE_CLOCK) then
      if(SOFT_RESET = '1' or (not(tx_state = INIT) and not(tx_state = ASSERT_ALL_RESETS) and refclk_lost = '1')) then
        tx_state                <= INIT;
        TXUSERRDY               <= '0';
        GTTXRESET               <= '0';
        MMCM_RESET              <= '1';
        tx_fsm_reset_done_int   <= '0';
        QPLL_RESET              <= '0';
        CPLL_RESET              <= '0';
        pll_reset_asserted      <= '0';
        reset_time_out          <= '0';
        retry_counter_int       <=  0;
        run_phase_alignment_int <= '0';
        RESET_PHALIGNMENT       <= '1';
      else
        
        case tx_state is
          when INIT => 
            --Initial state after configuration. This state will be left after
            --approx. 500 ns and not be re-entered. 
            if init_wait_done = '1' then
              tx_state        <= ASSERT_ALL_RESETS;
              reset_time_out  <= '1';
            end if;
            
          when ASSERT_ALL_RESETS => 
            --This is the state into which the FSM will always jump back if any
            --time-outs will occur. 
            --The number of retries is reported on the output RETRY_COUNTER. In 
            --case the transceiver never comes up for some reason, this machine 
            --will still continue its best and rerun until the FPGA is turned off
            --or the transceivers come up correctly.
            if TX_QPLL_USED then
              if pll_reset_asserted = '0' then
                QPLL_RESET          <= '1';
                pll_reset_asserted  <= '1';
              else
                QPLL_RESET          <= '0';
              end if;
            else
              if pll_reset_asserted = '0' then
                CPLL_RESET <= '1';
                pll_reset_asserted  <= '1';
              else
                CPLL_RESET          <= '0';
              end if;  
            end if;
            TXUSERRDY               <= '0';
            GTTXRESET               <= '1';
            MMCM_RESET              <= '1';
            reset_time_out          <= '0';
            run_phase_alignment_int <= '0';     
            RESET_PHALIGNMENT       <= '1';

            if (TX_QPLL_USED and (QPLLREFCLKLOST = '0') and pll_reset_asserted = '1') or
               (not TX_QPLL_USED and (CPLLREFCLKLOST = '0') and pll_reset_asserted = '1') then
              tx_state  <= RELEASE_PLL_RESET;
           end if;           
            
          when RELEASE_PLL_RESET => 
            --PLL-Reset of the GTX gets released and the time-out counter
            --starts running.
            pll_reset_asserted  <= '0';

             if (TX_QPLL_USED and (qplllock_ris_edge = '1')) or
               (not TX_QPLL_USED and (cplllock_ris_edge = '1')) then
              tx_state  <= RELEASE_MMCM_RESET;
              reset_time_out  <= '1';
            end if;
            
            if time_out_2ms = '1' then
              if retry_counter_int = MAX_RETRIES then
                -- If too many retries are performed compared to what is specified in 
                -- the generic, the counter simply wraps around.
                retry_counter_int <= 0;
              else
                retry_counter_int <= retry_counter_int + 1;
              end if;
              tx_state            <= ASSERT_ALL_RESETS; 
            end if;           

          when RELEASE_MMCM_RESET => 
            GTTXRESET <= '0';
            reset_time_out  <= '0';
            --Release of the MMCM-reset. Waiting for the MMCM to lock.
            MMCM_RESET <= '0';
            if mmcm_lock_reclocked = '1' then
              tx_state <= WAIT_RESET_DONE;
              reset_time_out  <= '1';
            end if;          
            
            if (time_tlock_max = '1' and mmcm_lock_reclocked = '0' and reset_time_out = '0') then
              if retry_counter_int = MAX_RETRIES then
                -- If too many retries are performed compared to what is specified in 
                -- the generic, the counter simply wraps around.
                retry_counter_int <= 0;
              else
                retry_counter_int <= retry_counter_int + 1;
              end if;
              tx_state            <= ASSERT_ALL_RESETS; 
            end if;            
            
          when WAIT_RESET_DONE => 
            TXUSERRDY <= '1';
            reset_time_out  <= '0';
            if txresetdone_s3 = '1' then              
              tx_state      <= DO_PHASE_ALIGNMENT;               
              reset_time_out  <= '1';
            end if;          

            if (time_out_500us = '1' and reset_time_out = '0') then
              if retry_counter_int = MAX_RETRIES then
                -- If too many retries are performed compared to what is specified in 
                -- the generic, the counter simply wraps around.
                retry_counter_int <= 0;
              else
                retry_counter_int <= retry_counter_int + 1;
              end if;
              tx_state            <= ASSERT_ALL_RESETS; 
            end if;                    
          
          when DO_PHASE_ALIGNMENT => 
            --The direct handling of the signals for the Phase Alignment is done outside
            --this state-machine. 
            RESET_PHALIGNMENT       <= '0';
            run_phase_alignment_int <= '1';
            reset_time_out          <= '0';
            
            if PHALIGNMENT_DONE = '1' then
              tx_state        <= RESET_FSM_DONE;
            end if;
            
            if time_out_wait_bypass_s3 = '1' then
              if retry_counter_int = MAX_RETRIES then
                -- If too many retries are performed compared to what is specified in 
                -- the generic, the counter simply wraps around.
                retry_counter_int <= 0;
              else
                retry_counter_int <=  retry_counter_int + 1;
              end if;
              tx_state            <= ASSERT_ALL_RESETS; 
            end if;           
          
          when RESET_FSM_DONE => 
            reset_time_out        <= '1';
            tx_fsm_reset_done_int <= '1';

          when OTHERS =>
            tx_state              <= INIT;
          
        end case;
      end if;
    end if;
  end process; 

end RTL;