AMC13
Firmwares for the different applications of the AMC13 uTCA board made at Boston University
 All Classes Variables
mig_7series_v1_9_bank_mach.v
1  //*****************************************************************************
2 // (c) Copyright 2008 - 2013 Xilinx, Inc. All rights reserved.
3 //
4 // This file contains confidential and proprietary information
5 // of Xilinx, Inc. and is protected under U.S. and
6 // international copyright and other intellectual property
7 // laws.
8 //
9 // DISCLAIMER
10 // This disclaimer is not a license and does not grant any
11 // rights to the materials distributed herewith. Except as
12 // otherwise provided in a valid license issued to you by
13 // Xilinx, and to the maximum extent permitted by applicable
14 // law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
15 // WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
16 // AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
17 // BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
18 // INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
19 // (2) Xilinx shall not be liable (whether in contract or tort,
20 // including negligence, or under any other theory of
21 // liability) for any loss or damage of any kind or nature
22 // related to, arising under or in connection with these
23 // materials, including for any direct, or any indirect,
24 // special, incidental, or consequential loss or damage
25 // (including loss of data, profits, goodwill, or any type of
26 // loss or damage suffered as a result of any action brought
27 // by a third party) even if such damage or loss was
28 // reasonably foreseeable or Xilinx had been advised of the
29 // possibility of the same.
30 //
31 // CRITICAL APPLICATIONS
32 // Xilinx products are not designed or intended to be fail-
33 // safe, or for use in any application requiring fail-safe
34 // performance, such as life-support or safety devices or
35 // systems, Class III medical devices, nuclear facilities,
36 // applications related to the deployment of airbags, or any
37 // other applications that could lead to death, personal
38 // injury, or severe property or environmental damage
39 // (individually and collectively, "Critical
40 // Applications"). Customer assumes the sole risk and
41 // liability of any use of Xilinx products in Critical
42 // Applications, subject only to applicable laws and
43 // regulations governing limitations on product liability.
44 //
45 // THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
46 // PART OF THIS FILE AT ALL TIMES.
47 //
48 //*****************************************************************************
49 // ____ ____
50 // / /\/ /
51 // /___/ \ / Vendor : Xilinx
52 // \ \ \/ Version : %version
53 // \ \ Application : MIG
54 // / / Filename : bank_mach.v
55 // /___/ /\ Date Last Modified : $date$
56 // \ \ / \ Date Created : Tue Jun 30 2009
57 // \___\/\___\
58 //
59 //Device : 7-Series
60 //Design Name : DDR3 SDRAM
61 //Purpose :
62 //Reference :
63 //Revision History :
64 //*****************************************************************************
65 
66 // Top level bank machine block. A structural block instantiating the configured
67 // individual bank machines, and a common block that computes various items shared
68 // by all bank machines.
69 
70 `timescale 1ps/1ps
71 
72 module mig_7series_v1_9_bank_mach #
73  (
74  parameter TCQ = 100,
75  parameter EVEN_CWL_2T_MODE = "OFF",
76  parameter ADDR_CMD_MODE = "1T",
77  parameter BANK_WIDTH = 3,
78  parameter BM_CNT_WIDTH = 2,
79  parameter BURST_MODE = "8",
80  parameter COL_WIDTH = 12,
81  parameter CS_WIDTH = 4,
82  parameter CL = 5,
83  parameter CWL = 5,
84  parameter DATA_BUF_ADDR_WIDTH = 8,
85  parameter DRAM_TYPE = "DDR3",
86  parameter EARLY_WR_DATA_ADDR = "OFF",
87  parameter ECC = "OFF",
88  parameter LOW_IDLE_CNT = 1,
89  parameter nBANK_MACHS = 4,
90  parameter nCK_PER_CLK = 2,
91  parameter nCS_PER_RANK = 1,
92  parameter nOP_WAIT = 0,
93  parameter nRAS = 20,
94  parameter nRCD = 5,
95  parameter nRFC = 44,
96  parameter nRTP = 4,
97  parameter CKE_ODT_AUX = "FALSE", //Parameter to turn on/off the aux_out signal
98  parameter nRP = 10,
99  parameter nSLOTS = 2,
100  parameter nWR = 6,
101  parameter nXSDLL = 512,
102  parameter ORDERING = "NORM",
103  parameter RANK_BM_BV_WIDTH = 16,
104  parameter RANK_WIDTH = 2,
105  parameter RANKS = 4,
106  parameter ROW_WIDTH = 16,
107  parameter RTT_NOM = "40",
108  parameter RTT_WR = "120",
109  parameter STARVE_LIMIT = 2,
110  parameter SLOT_0_CONFIG = 8'b0000_0101,
111  parameter SLOT_1_CONFIG = 8'b0000_1010,
112  parameter tZQCS = 64
113  )
114  (/*AUTOARG**/
115  // Outputs
116  output accept, // From bank_common0 of bank_common.v
117  output accept_ns, // From bank_common0 of bank_common.v
118  output [BM_CNT_WIDTH-1:0] bank_mach_next, // From bank_common0 of bank_common.v
119  output [ROW_WIDTH-1:0] col_a, // From arb_mux0 of arb_mux.v
120  output [BANK_WIDTH-1:0] col_ba, // From arb_mux0 of arb_mux.v
121  output [DATA_BUF_ADDR_WIDTH-1:0] col_data_buf_addr,// From arb_mux0 of arb_mux.v
122  output col_periodic_rd, // From arb_mux0 of arb_mux.v
123  output [RANK_WIDTH-1:0] col_ra, // From arb_mux0 of arb_mux.v
124  output col_rmw, // From arb_mux0 of arb_mux.v
125  output col_rd_wr,
126  output [ROW_WIDTH-1:0] col_row, // From arb_mux0 of arb_mux.v
127  output col_size, // From arb_mux0 of arb_mux.v
128  output [DATA_BUF_ADDR_WIDTH-1:0] col_wr_data_buf_addr,// From arb_mux0 of arb_mux.v
129  output wire [nCK_PER_CLK-1:0] mc_ras_n,
130  output wire [nCK_PER_CLK-1:0] mc_cas_n,
131  output wire [nCK_PER_CLK-1:0] mc_we_n,
132  output wire [nCK_PER_CLK*ROW_WIDTH-1:0] mc_address,
133  output wire [nCK_PER_CLK*BANK_WIDTH-1:0] mc_bank,
134  output wire [CS_WIDTH*nCS_PER_RANK*nCK_PER_CLK-1:0] mc_cs_n,
135  output wire [1:0] mc_odt,
136  output wire [nCK_PER_CLK-1:0] mc_cke,
137  output wire [3:0] mc_aux_out0,
138  output wire [3:0] mc_aux_out1,
139  output [2:0] mc_cmd,
140  output [5:0] mc_data_offset,
141  output [5:0] mc_data_offset_1,
142  output [5:0] mc_data_offset_2,
143  output [1:0] mc_cas_slot,
144  output insert_maint_r1, // From arb_mux0 of arb_mux.v
145  output maint_wip_r, // From bank_common0 of bank_common.v
146  output wire [nBANK_MACHS-1:0] sending_row,
147  output wire [nBANK_MACHS-1:0] sending_col,
148  output wire sent_col,
149  output wire sent_col_r,
150  output periodic_rd_ack_r,
151  output wire [RANK_BM_BV_WIDTH-1:0] act_this_rank_r,
152  output wire [RANK_BM_BV_WIDTH-1:0] wr_this_rank_r,
153  output wire [RANK_BM_BV_WIDTH-1:0] rd_this_rank_r,
154  output wire [(RANKS*nBANK_MACHS)-1:0] rank_busy_r,
155  output idle,
156 
157  // Inputs
158  input [BANK_WIDTH-1:0] bank, // To bank0 of bank_cntrl.v
159  input [6*RANKS-1:0] calib_rddata_offset,
160  input [6*RANKS-1:0] calib_rddata_offset_1,
161  input [6*RANKS-1:0] calib_rddata_offset_2,
162  input clk, // To bank0 of bank_cntrl.v, ...
163  input [2:0] cmd, // To bank0 of bank_cntrl.v, ...
164  input [COL_WIDTH-1:0] col, // To bank0 of bank_cntrl.v
165  input [DATA_BUF_ADDR_WIDTH-1:0] data_buf_addr,// To bank0 of bank_cntrl.v
166  input init_calib_complete, // To bank_common0 of bank_common.v
167  input phy_rddata_valid, // To bank0 of bank_cntrl.v
168  input dq_busy_data, // To bank0 of bank_cntrl.v
169  input hi_priority, // To bank0 of bank_cntrl.v, ...
170  input [RANKS-1:0] inhbt_act_faw_r, // To bank0 of bank_cntrl.v
171  input [RANKS-1:0] inhbt_rd, // To bank0 of bank_cntrl.v
172  input [RANKS-1:0] inhbt_wr, // To bank0 of bank_cntrl.v
173  input [RANK_WIDTH-1:0] maint_rank_r, // To bank0 of bank_cntrl.v, ...
174  input maint_req_r, // To bank0 of bank_cntrl.v, ...
175  input maint_zq_r, // To bank0 of bank_cntrl.v, ...
176  input maint_sre_r, // To bank0 of bank_cntrl.v, ...
177  input maint_srx_r, // To bank0 of bank_cntrl.v, ...
178  input periodic_rd_r, // To bank_common0 of bank_common.v
179  input [RANK_WIDTH-1:0] periodic_rd_rank_r, // To bank0 of bank_cntrl.v
180  input phy_mc_ctl_full,
181  input phy_mc_cmd_full,
182  input phy_mc_data_full,
183  input [RANK_WIDTH-1:0] rank, // To bank0 of bank_cntrl.v
184  input [DATA_BUF_ADDR_WIDTH-1:0] rd_data_addr, // To bank0 of bank_cntrl.v
185  input rd_rmw, // To bank0 of bank_cntrl.v
186  input [ROW_WIDTH-1:0] row, // To bank0 of bank_cntrl.v
187  input rst, // To bank0 of bank_cntrl.v, ...
188  input size, // To bank0 of bank_cntrl.v
189  input [7:0] slot_0_present, // To bank_common0 of bank_common.v, ...
190  input [7:0] slot_1_present, // To bank_common0 of bank_common.v, ...
191  input use_addr
192  );
193 
194  function integer clogb2 (input integer size); // ceiling logb2
195  begin
196  size = size - 1;
197  for (clogb2=1; size>1; clogb2=clogb2+1)
198  size = size >> 1;
199  end
200  endfunction // clogb2
201 
202  localparam RANK_VECT_INDX = (nBANK_MACHS *RANK_WIDTH) - 1;
203  localparam BANK_VECT_INDX = (nBANK_MACHS * BANK_WIDTH) - 1;
204  localparam ROW_VECT_INDX = (nBANK_MACHS * ROW_WIDTH) - 1;
205  localparam DATA_BUF_ADDR_VECT_INDX = (nBANK_MACHS * DATA_BUF_ADDR_WIDTH) - 1;
206  localparam nRAS_CLKS = (nCK_PER_CLK == 1) ? nRAS : (nCK_PER_CLK == 2) ? ((nRAS/2) + (nRAS % 2)) : ((nRAS/4) + ((nRAS%4) ? 1 : 0));
207  localparam nWTP = CWL + ((BURST_MODE == "4") ? 2 : 4) + nWR;
208 // Unless 2T mode, add one to nWTP_CLKS for 2:1 mode. This accounts for loss of
209 // one DRAM CK due to column command to row command fixed offset. In 2T mode,
210 // Add the remainder. In 4:1 mode, the fixed offset is -2. Add 2 unless in 2T
211 // mode, in which case we add 1 if the remainder exceeds the fixed offset.
212  localparam nWTP_CLKS = (nCK_PER_CLK == 1)
213  ? nWTP :
214  (nCK_PER_CLK == 2)
215  ? (nWTP/2) + ((ADDR_CMD_MODE == "2T") ? nWTP%2 : 1) :
216  (nWTP/4) + ((ADDR_CMD_MODE == "2T") ? (nWTP%4 > 2 ? 2 : 1) : 2);
217  localparam RAS_TIMER_WIDTH = clogb2(((nRAS_CLKS > nWTP_CLKS)
218  ? nRAS_CLKS
219  : nWTP_CLKS) - 1);
220 
221  /*AUTOINPUT**/
222  // Beginning of automatic inputs (from unused autoinst inputs)
223 
224  // End of automatics
225 
226  /*AUTOOUTPUT**/
227  // Beginning of automatic outputs (from unused autoinst outputs)
228 
229  // End of automatics
230 
231  /*AUTOWIRE**/
232  // Beginning of automatic wires (for undeclared instantiated-module outputs)
233  wire accept_internal_r; // From bank_common0 of bank_common.v
234  wire accept_req; // From bank_common0 of bank_common.v
235  wire adv_order_q; // From bank_common0 of bank_common.v
236  wire [BM_CNT_WIDTH-1:0] idle_cnt; // From bank_common0 of bank_common.v
237  wire insert_maint_r; // From bank_common0 of bank_common.v
238  wire low_idle_cnt_r; // From bank_common0 of bank_common.v
239  wire maint_idle; // From bank_common0 of bank_common.v
240  wire [BM_CNT_WIDTH-1:0] order_cnt; // From bank_common0 of bank_common.v
241  wire periodic_rd_insert; // From bank_common0 of bank_common.v
242  wire [BM_CNT_WIDTH-1:0] rb_hit_busy_cnt; // From bank_common0 of bank_common.v
243  wire sent_row; // From arb_mux0 of arb_mux.v
244  wire was_priority; // From bank_common0 of bank_common.v
245  wire was_wr; // From bank_common0 of bank_common.v
246  // End of automatics
247 
248  wire [RANK_WIDTH-1:0] rnk_config;
249  wire rnk_config_strobe;
250  wire rnk_config_kill_rts_col;
251  wire rnk_config_valid_r;
252 
253  wire [nBANK_MACHS-1:0] rts_row;
254  wire [nBANK_MACHS-1:0] rts_col;
255  wire [nBANK_MACHS-1:0] rts_pre;
256  wire [nBANK_MACHS-1:0] col_rdy_wr;
257  wire [nBANK_MACHS-1:0] rtc;
258  wire [nBANK_MACHS-1:0] sending_pre;
259 
260  wire [DATA_BUF_ADDR_VECT_INDX:0] req_data_buf_addr_r;
261  wire [nBANK_MACHS-1:0] req_size_r;
262  wire [RANK_VECT_INDX:0] req_rank_r;
263  wire [BANK_VECT_INDX:0] req_bank_r;
264  wire [ROW_VECT_INDX:0] req_row_r;
265  wire [ROW_VECT_INDX:0] col_addr;
266  wire [nBANK_MACHS-1:0] req_periodic_rd_r;
267  wire [nBANK_MACHS-1:0] req_wr_r;
268  wire [nBANK_MACHS-1:0] rd_wr_r;
269  wire [nBANK_MACHS-1:0] req_ras;
270  wire [nBANK_MACHS-1:0] req_cas;
271  wire [ROW_VECT_INDX:0] row_addr;
272  wire [nBANK_MACHS-1:0] row_cmd_wr;
273  wire [nBANK_MACHS-1:0] demand_priority;
274  wire [nBANK_MACHS-1:0] demand_act_priority;
275 
276  wire [nBANK_MACHS-1:0] idle_ns;
277  wire [nBANK_MACHS-1:0] rb_hit_busy_r;
278  wire [nBANK_MACHS-1:0] bm_end;
279  wire [nBANK_MACHS-1:0] passing_open_bank;
280  wire [nBANK_MACHS-1:0] ordered_r;
281  wire [nBANK_MACHS-1:0] ordered_issued;
282  wire [nBANK_MACHS-1:0] rb_hit_busy_ns;
283  wire [nBANK_MACHS-1:0] maint_hit;
284  wire [nBANK_MACHS-1:0] idle_r;
285  wire [nBANK_MACHS-1:0] head_r;
286  wire [nBANK_MACHS-1:0] start_rcd;
287 
288  wire [nBANK_MACHS-1:0] end_rtp;
289  wire [nBANK_MACHS-1:0] op_exit_req;
290  wire [nBANK_MACHS-1:0] op_exit_grant;
291  wire [nBANK_MACHS-1:0] start_pre_wait;
292 
293  wire [(RAS_TIMER_WIDTH*nBANK_MACHS)-1:0] ras_timer_ns;
294 
295  genvar ID;
296  generate for (ID=0; ID<nBANK_MACHS; ID=ID+1) begin:bank_cntrl
297  mig_7series_v1_9_bank_cntrl #
298  (/*AUTOINSTPARAM**/
299  // Parameters
300  .TCQ (TCQ),
301  .ADDR_CMD_MODE (ADDR_CMD_MODE),
302  .BANK_WIDTH (BANK_WIDTH),
303  .BM_CNT_WIDTH (BM_CNT_WIDTH),
304  .BURST_MODE (BURST_MODE),
305  .COL_WIDTH (COL_WIDTH),
306  .CWL (CWL),
307  .DATA_BUF_ADDR_WIDTH (DATA_BUF_ADDR_WIDTH),
308  .DRAM_TYPE (DRAM_TYPE),
309  .ECC (ECC),
310  .ID (ID),
311  .nBANK_MACHS (nBANK_MACHS),
312  .nCK_PER_CLK (nCK_PER_CLK),
313  .nOP_WAIT (nOP_WAIT),
314  .nRAS_CLKS (nRAS_CLKS),
315  .nRCD (nRCD),
316  .nRTP (nRTP),
317  .nRP (nRP),
318  .nWTP_CLKS (nWTP_CLKS),
319  .ORDERING (ORDERING),
320  .RANK_WIDTH (RANK_WIDTH),
321  .RANKS (RANKS),
322  .RAS_TIMER_WIDTH (RAS_TIMER_WIDTH),
323  .ROW_WIDTH (ROW_WIDTH),
324  .STARVE_LIMIT (STARVE_LIMIT))
325  bank0
326  (.demand_priority (demand_priority[ID]),
327  .demand_priority_in ({2{demand_priority}}),
328  .demand_act_priority (demand_act_priority[ID]),
329  .demand_act_priority_in ({2{demand_act_priority}}),
330  .rts_row (rts_row[ID]),
331  .rts_col (rts_col[ID]),
332  .rts_pre (rts_pre[ID]),
333  .col_rdy_wr (col_rdy_wr[ID]),
334  .rtc (rtc[ID]),
335  .sending_row (sending_row[ID]),
336  .sending_pre (sending_pre[ID]),
337  .sending_col (sending_col[ID]),
338  .req_data_buf_addr_r (req_data_buf_addr_r[(ID*DATA_BUF_ADDR_WIDTH)+:DATA_BUF_ADDR_WIDTH]),
339  .req_size_r (req_size_r[ID]),
340  .req_rank_r (req_rank_r[(ID*RANK_WIDTH)+:RANK_WIDTH]),
341  .req_bank_r (req_bank_r[(ID*BANK_WIDTH)+:BANK_WIDTH]),
342  .req_row_r (req_row_r[(ID*ROW_WIDTH)+:ROW_WIDTH]),
343  .col_addr (col_addr[(ID*ROW_WIDTH)+:ROW_WIDTH]),
344  .req_wr_r (req_wr_r[ID]),
345  .rd_wr_r (rd_wr_r[ID]),
346  .req_periodic_rd_r (req_periodic_rd_r[ID]),
347  .req_ras (req_ras[ID]),
348  .req_cas (req_cas[ID]),
349  .row_addr (row_addr[(ID*ROW_WIDTH)+:ROW_WIDTH]),
350  .row_cmd_wr (row_cmd_wr[ID]),
351  .act_this_rank_r (act_this_rank_r[(ID*RANKS)+:RANKS]),
352  .wr_this_rank_r (wr_this_rank_r[(ID*RANKS)+:RANKS]),
353  .rd_this_rank_r (rd_this_rank_r[(ID*RANKS)+:RANKS]),
354  .idle_ns (idle_ns[ID]),
355  .rb_hit_busy_r (rb_hit_busy_r[ID]),
356  .bm_end (bm_end[ID]),
357  .bm_end_in ({2{bm_end}}),
358  .passing_open_bank (passing_open_bank[ID]),
359  .passing_open_bank_in ({2{passing_open_bank}}),
360  .ordered_r (ordered_r[ID]),
361  .ordered_issued (ordered_issued[ID]),
362  .rb_hit_busy_ns (rb_hit_busy_ns[ID]),
363  .rb_hit_busy_ns_in ({2{rb_hit_busy_ns}}),
364  .maint_hit (maint_hit[ID]),
365  .req_rank_r_in ({2{req_rank_r}}),
366  .idle_r (idle_r[ID]),
367  .head_r (head_r[ID]),
368  .start_rcd (start_rcd[ID]),
369  .start_rcd_in ({2{start_rcd}}),
370  .end_rtp (end_rtp[ID]),
371  .op_exit_req (op_exit_req[ID]),
372  .op_exit_grant (op_exit_grant[ID]),
373  .start_pre_wait (start_pre_wait[ID]),
374  .ras_timer_ns (ras_timer_ns[(ID*RAS_TIMER_WIDTH)+:RAS_TIMER_WIDTH]),
375  .ras_timer_ns_in ({2{ras_timer_ns}}),
376  .rank_busy_r (rank_busy_r[ID*RANKS+:RANKS]),
377  /*AUTOINST**/
378  // Inputs
379  .accept_internal_r (accept_internal_r),
380  .accept_req (accept_req),
381  .adv_order_q (adv_order_q),
382  .bank (bank[BANK_WIDTH-1:0]),
383  .clk (clk),
384  .cmd (cmd[2:0]),
385  .col (col[COL_WIDTH-1:0]),
386  .data_buf_addr (data_buf_addr[DATA_BUF_ADDR_WIDTH-1:0]),
387  .phy_rddata_valid (phy_rddata_valid),
388  .dq_busy_data (dq_busy_data),
389  .hi_priority (hi_priority),
390  .idle_cnt (idle_cnt[BM_CNT_WIDTH-1:0]),
391  .inhbt_act_faw_r (inhbt_act_faw_r[RANKS-1:0]),
392  .inhbt_rd (inhbt_rd[RANKS-1:0]),
393  .inhbt_wr (inhbt_wr[RANKS-1:0]),
394  .rnk_config (rnk_config[RANK_WIDTH-1:0]),
395  .rnk_config_strobe (rnk_config_strobe),
396  .rnk_config_kill_rts_col (rnk_config_kill_rts_col),
397  .rnk_config_valid_r (rnk_config_valid_r),
398  .low_idle_cnt_r (low_idle_cnt_r),
399  .maint_idle (maint_idle),
400  .maint_rank_r (maint_rank_r[RANK_WIDTH-1:0]),
401  .maint_req_r (maint_req_r),
402  .maint_zq_r (maint_zq_r),
403  .maint_sre_r (maint_sre_r),
404  .order_cnt (order_cnt[BM_CNT_WIDTH-1:0]),
405  .periodic_rd_ack_r (periodic_rd_ack_r),
406  .periodic_rd_insert (periodic_rd_insert),
407  .periodic_rd_rank_r (periodic_rd_rank_r[RANK_WIDTH-1:0]),
408  .phy_mc_cmd_full (phy_mc_cmd_full),
409  .phy_mc_ctl_full (phy_mc_ctl_full),
410  .phy_mc_data_full (phy_mc_data_full),
411  .rank (rank[RANK_WIDTH-1:0]),
412  .rb_hit_busy_cnt (rb_hit_busy_cnt[BM_CNT_WIDTH-1:0]),
413  .rd_data_addr (rd_data_addr[DATA_BUF_ADDR_WIDTH-1:0]),
414  .rd_rmw (rd_rmw),
415  .row (row[ROW_WIDTH-1:0]),
416  .rst (rst),
417  .sent_col (sent_col),
418  .sent_row (sent_row),
419  .size (size),
420  .use_addr (use_addr),
421  .was_priority (was_priority),
422  .was_wr (was_wr));
423  end
424  endgenerate
425 
426  mig_7series_v1_9_bank_common #
427  (/*AUTOINSTPARAM**/
428  // Parameters
429  .TCQ (TCQ),
430  .BM_CNT_WIDTH (BM_CNT_WIDTH),
431  .LOW_IDLE_CNT (LOW_IDLE_CNT),
432  .nBANK_MACHS (nBANK_MACHS),
433  .nCK_PER_CLK (nCK_PER_CLK),
434  .nOP_WAIT (nOP_WAIT),
435  .nRFC (nRFC),
436  .nXSDLL (nXSDLL),
437  .RANK_WIDTH (RANK_WIDTH),
438  .RANKS (RANKS),
439  .CWL (CWL),
440  .tZQCS (tZQCS))
441  bank_common0
442  (.op_exit_grant (op_exit_grant[nBANK_MACHS-1:0]),
443  /*AUTOINST**/
444  // Outputs
445  .accept_internal_r (accept_internal_r),
446  .accept_ns (accept_ns),
447  .accept (accept),
448  .periodic_rd_insert (periodic_rd_insert),
449  .periodic_rd_ack_r (periodic_rd_ack_r),
450  .accept_req (accept_req),
451  .rb_hit_busy_cnt (rb_hit_busy_cnt[BM_CNT_WIDTH-1:0]),
452  .idle_cnt (idle_cnt[BM_CNT_WIDTH-1:0]),
453  .idle (idle),
454  .order_cnt (order_cnt[BM_CNT_WIDTH-1:0]),
455  .adv_order_q (adv_order_q),
456  .bank_mach_next (bank_mach_next[BM_CNT_WIDTH-1:0]),
457  .low_idle_cnt_r (low_idle_cnt_r),
458  .was_wr (was_wr),
459  .was_priority (was_priority),
460  .maint_wip_r (maint_wip_r),
461  .maint_idle (maint_idle),
462  .insert_maint_r (insert_maint_r),
463  // Inputs
464  .clk (clk),
465  .rst (rst),
466  .idle_ns (idle_ns[nBANK_MACHS-1:0]),
467  .init_calib_complete (init_calib_complete),
468  .periodic_rd_r (periodic_rd_r),
469  .use_addr (use_addr),
470  .rb_hit_busy_r (rb_hit_busy_r[nBANK_MACHS-1:0]),
471  .idle_r (idle_r[nBANK_MACHS-1:0]),
472  .ordered_r (ordered_r[nBANK_MACHS-1:0]),
473  .ordered_issued (ordered_issued[nBANK_MACHS-1:0]),
474  .head_r (head_r[nBANK_MACHS-1:0]),
475  .end_rtp (end_rtp[nBANK_MACHS-1:0]),
476  .passing_open_bank (passing_open_bank[nBANK_MACHS-1:0]),
477  .op_exit_req (op_exit_req[nBANK_MACHS-1:0]),
478  .start_pre_wait (start_pre_wait[nBANK_MACHS-1:0]),
479  .cmd (cmd[2:0]),
480  .hi_priority (hi_priority),
481  .maint_req_r (maint_req_r),
482  .maint_zq_r (maint_zq_r),
483  .maint_sre_r (maint_sre_r),
484  .maint_srx_r (maint_srx_r),
485  .maint_hit (maint_hit[nBANK_MACHS-1:0]),
486  .bm_end (bm_end[nBANK_MACHS-1:0]),
487  .slot_0_present (slot_0_present[7:0]),
488  .slot_1_present (slot_1_present[7:0]));
489 
490  mig_7series_v1_9_arb_mux #
491  (/*AUTOINSTPARAM**/
492  // Parameters
493  .TCQ (TCQ),
494  .EVEN_CWL_2T_MODE (EVEN_CWL_2T_MODE),
495  .ADDR_CMD_MODE (ADDR_CMD_MODE),
496  .BANK_VECT_INDX (BANK_VECT_INDX),
497  .BANK_WIDTH (BANK_WIDTH),
498  .BURST_MODE (BURST_MODE),
499  .CS_WIDTH (CS_WIDTH),
500  .CL (CL),
501  .CWL (CWL),
502  .DATA_BUF_ADDR_VECT_INDX (DATA_BUF_ADDR_VECT_INDX),
503  .DATA_BUF_ADDR_WIDTH (DATA_BUF_ADDR_WIDTH),
504  .DRAM_TYPE (DRAM_TYPE),
505  .EARLY_WR_DATA_ADDR (EARLY_WR_DATA_ADDR),
506  .ECC (ECC),
507  .nBANK_MACHS (nBANK_MACHS),
508  .nCK_PER_CLK (nCK_PER_CLK),
509  .nCS_PER_RANK (nCS_PER_RANK),
510  .nRAS (nRAS),
511  .nRCD (nRCD),
512  .CKE_ODT_AUX (CKE_ODT_AUX),
513  .nSLOTS (nSLOTS),
514  .nWR (nWR),
515  .RANKS (RANKS),
516  .RANK_VECT_INDX (RANK_VECT_INDX),
517  .RANK_WIDTH (RANK_WIDTH),
518  .ROW_VECT_INDX (ROW_VECT_INDX),
519  .ROW_WIDTH (ROW_WIDTH),
520  .RTT_NOM (RTT_NOM),
521  .RTT_WR (RTT_WR),
522  .SLOT_0_CONFIG (SLOT_0_CONFIG),
523  .SLOT_1_CONFIG (SLOT_1_CONFIG))
524  arb_mux0
525  (.rts_col (rts_col[nBANK_MACHS-1:0]), // AUTOs wants to make this an input.
526  /*AUTOINST**/
527  // Outputs
528  .col_a (col_a[ROW_WIDTH-1:0]),
529  .col_ba (col_ba[BANK_WIDTH-1:0]),
530  .col_data_buf_addr (col_data_buf_addr[DATA_BUF_ADDR_WIDTH-1:0]),
531  .col_periodic_rd (col_periodic_rd),
532  .col_ra (col_ra[RANK_WIDTH-1:0]),
533  .col_rmw (col_rmw),
534  .col_rd_wr (col_rd_wr),
535  .col_row (col_row[ROW_WIDTH-1:0]),
536  .col_size (col_size),
537  .col_wr_data_buf_addr (col_wr_data_buf_addr[DATA_BUF_ADDR_WIDTH-1:0]),
538  .mc_bank (mc_bank),
539  .mc_address (mc_address),
540  .mc_ras_n (mc_ras_n),
541  .mc_cas_n (mc_cas_n),
542  .mc_we_n (mc_we_n),
543  .mc_cs_n (mc_cs_n),
544  .mc_odt (mc_odt),
545  .mc_cke (mc_cke),
546  .mc_aux_out0 (mc_aux_out0),
547  .mc_aux_out1 (mc_aux_out1),
548  .mc_cmd (mc_cmd),
549  .mc_data_offset (mc_data_offset),
550  .mc_data_offset_1 (mc_data_offset_1),
551  .mc_data_offset_2 (mc_data_offset_2),
552  .rnk_config (rnk_config[RANK_WIDTH-1:0]),
553  .rnk_config_valid_r (rnk_config_valid_r),
554  .mc_cas_slot (mc_cas_slot),
555  .sending_row (sending_row[nBANK_MACHS-1:0]),
556  .sending_pre (sending_pre[nBANK_MACHS-1:0]),
557  .sent_col (sent_col),
558  .sent_col_r (sent_col_r),
559  .sent_row (sent_row),
560  .sending_col (sending_col[nBANK_MACHS-1:0]),
561  .rnk_config_strobe (rnk_config_strobe),
562  .rnk_config_kill_rts_col (rnk_config_kill_rts_col),
563  .insert_maint_r1 (insert_maint_r1),
564  // Inputs
565  .init_calib_complete (init_calib_complete),
566  .calib_rddata_offset (calib_rddata_offset),
567  .calib_rddata_offset_1 (calib_rddata_offset_1),
568  .calib_rddata_offset_2 (calib_rddata_offset_2),
569  .col_addr (col_addr[ROW_VECT_INDX:0]),
570  .col_rdy_wr (col_rdy_wr[nBANK_MACHS-1:0]),
571  .insert_maint_r (insert_maint_r),
572  .maint_rank_r (maint_rank_r[RANK_WIDTH-1:0]),
573  .maint_zq_r (maint_zq_r),
574  .maint_sre_r (maint_sre_r),
575  .maint_srx_r (maint_srx_r),
576  .rd_wr_r (rd_wr_r[nBANK_MACHS-1:0]),
577  .req_bank_r (req_bank_r[BANK_VECT_INDX:0]),
578  .req_cas (req_cas[nBANK_MACHS-1:0]),
579  .req_data_buf_addr_r (req_data_buf_addr_r[DATA_BUF_ADDR_VECT_INDX:0]),
580  .req_periodic_rd_r (req_periodic_rd_r[nBANK_MACHS-1:0]),
581  .req_rank_r (req_rank_r[RANK_VECT_INDX:0]),
582  .req_ras (req_ras[nBANK_MACHS-1:0]),
583  .req_row_r (req_row_r[ROW_VECT_INDX:0]),
584  .req_size_r (req_size_r[nBANK_MACHS-1:0]),
585  .req_wr_r (req_wr_r[nBANK_MACHS-1:0]),
586  .row_addr (row_addr[ROW_VECT_INDX:0]),
587  .row_cmd_wr (row_cmd_wr[nBANK_MACHS-1:0]),
588  .rts_row (rts_row[nBANK_MACHS-1:0]),
589  .rtc (rtc[nBANK_MACHS-1:0]),
590  .rts_pre (rts_pre[nBANK_MACHS-1:0]),
591  .slot_0_present (slot_0_present[7:0]),
592  .slot_1_present (slot_1_present[7:0]),
593  .clk (clk),
594  .rst (rst));
595 
596 endmodule // bank_mach
Generated on Wed Apr 18 2018 10:55:27 for AMC13 by   doxygen 1.8.1